Packet Tracer - Configure Initial Router Settings

-

Configure Initial Router Settings

Part 1:     Verify the Default Router Configuration
Step 1:     Establish a console connection to R1.

Step 2 : Enter privileged mode and examine the current configuration.

Part 2 : Configure and Verify the Initial Router Configuration
Step 1:         Configure the initial settings on R1.
Step 2:     Verify the initial settings on R1.








Part 3 : Save the Running Configuration File

Step 3:         Optional bonus: Save the startup configuration file to flash.
 

Hasil Nilai :





Komentar

Posting Komentar

Postingan populer dari blog ini

Packet Tracer - Connect a Router to a LAN

-
Gambar
Connect a Router to a LAN 1. Click a device and then click the   CLI   tab to access the command line directly. The console password is   cisco . The privileged EXEC password is   class . a.        Which command displays the statistics for all interfaces configured on a router? b.       Which command displays the information about the Serial 0/0/0 interface only?      2.   Enter the following commands to address and activate the GigabitEthernet 0/0 interface on   R1 : R1(config)#   interface gigabitethernet 0/0 R1(config-if)#   ip address 192.168.10.1 255.255.255.0 R1(config-if)#   no shutdown %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up                                                                 4. It is good practice to configure a description for each interface to help docum
Baca selengkapnya

Packet Tracer - Configuring initial

-
Gambar
Configuring Initial Configure S1 : 1.  Enter privileged EXEC mode by entering the   enable   command: Switch>   enable Switch# 2.  Enter the   show running- config   command. Switch#   show running- config Switch#   configure terminal Switch( config )#   hostname S1 S1( config )#   exit S1# S1#   configure terminal Enter configuration commands, one per line. End with CNTL/Z. S1( config )#   line console 0 S1( config -line)#   password   letmein S1( config -line)#   login S1( config -line)#   exit S1( config )#   exit %SYS-5-CONFIG_I: Configured from console by console S1# S1#   exit Switch con0 is now available Press RETURN to get started. User Access Verification Password: S1> S1>   enable S1#   configure terminal S1( config )#   enable password c1$c0 S1( config )#   exit %SYS-5-CONFIG_I: Configured from console by console S1# a.        Enter the   exit   command again to log out of the switch. b.  
Baca selengkapnya

Konfigurasi Dasar EIGRP Routing Dan Konfigurasi Server Pada Router

-
Gambar
SKEMA 1   1. Gambar skema seperti dibawah ini :                                         2. Lalu langkah-langkah untuk melakukan konfigurasi EIGRP ialah masukkan alamat IP address pada masing-masing interface router. 3. Konfigurasi yg pertama dilakukan pada router "R1" adalah masukkan IP address 10.1.1.1/24 pada interface Fashethernet0/0 seperti dibawah ini :                       4. Setelah melakukan konfigurasi IP address pada int Fa0/0, sekarang masukkan konfigurasi untuk pembuatan EIGRPnya seperti dibawah ini :                 5. Selanjutnya kita akan melakukan konfigurasi pada R2, masukkan IP address 10.1.1.2/24 pada interface Fashethernet0/0 beserta konfigurasi EIGRPnya seperti dibawah ini :       6. Konfigurasi IP address dan EIGRP telah selesai kita lakukan, maka langkah selanjutnya melakukan test koneksi dengan melakukan Ping antara alamat Router1 dengan
Baca selengkapnya